CoR Skirt S Joint
CoR Skirt S Joint: Pre-formed cove base joint that connects two CoR Skirt lengths in a straight run, with flexible edges, in the CoRound™ Seal line. Fits the CoR Skirt S and the CoR Skirt B. Straight lengths meet at a joint piece, columns take pre-formed outside corners, and each run stops at an end cap at the door: no miter cuts to fill with silicone.
Colors: Pure White 9010, Sand White 9002.
No sealant line required along the wall
Pre-formed corners, no silicone-filled field cuts
No resin or cement to cure
No welding on site
Full Description
The cove base that goes in with the panels. The CoR Skirt S Joint is the cove base joint for the CoR Skirt, in the CoRound Seal line. It is a joint piece that connects two CoR Skirt lengths in a straight run, at the floor-to-wall juncture. It has flexible edges, and it also fits the CoR Skirt B of the Basic line.
What Is the CoR Skirt S Joint?
It is a joint piece with flexible edges that connects two CoR Skirt lengths in a straight run. It fits the CoR Skirt S and the CoR Skirt B.
However, it comes in Pure White 9010 and Sand White 9002 only. Seal Cap: A cap that covers the fastener holes on the Seal components, so the holes are not left open to collect dirt. Included with the Seal components; also available separately.
Why Use a Pre-formed Cove Base Joint?
Where two lengths meet, a joint made by hand can end up filled with silicone. Instead, the joint piece covers the meeting point. Straight lengths meet at a joint piece, columns take pre-formed outside corners, and each run stops at an end cap at the door: no miter cuts to fill with silicone. The curve comes from the factory, not from the installer’s hand: it is the same all the way around the room.
Where Does the Cove Base Joint Install?
It goes wherever a straight run of CoR Skirt is longer than one length. Typical rooms include:
- Walk-in coolers built with insulated panels
- Processing and packing rooms in food plants
- Commercial kitchens
On a CoR Skirt B run in Pure White 9010 or Sand White 9002, the same joint piece fits at the floor-to-wall juncture. At walls and ceiling, however, the CoR 4 has its own joint: the CoR 4 Joint. Both are sanitary cove base accessories made to fit their profile.
How Do You Install the CoR Skirt S Joint?
First, installers fasten the two CoR Skirt lengths to the wall, end to end. Then they press or snap the CoR Skirt S Joint into place over the meeting point. Silicone is optional: not required for installation.
If a corner piece or end cap leaves a gap, it is not fully seated: tap it into place with a rubber mallet. These instructions are general installation advice: the installer chooses the method that suits the job.
Order the CoR Skirt S Joint
Panelmart supplies this cove base joint and the other sanitary cove base accessories of the Seal line, so each straight run comes from one system. It also fits the CoR Skirt B of the CoRound Basic System. Browse the CoRound Seal System or all sanitary PVC profiles. Available by the box or by the piece.
Get a quote, specs or free samples for the CoR Skirt S Joint: call +1 786 917 8106, email [email protected], or contact Panelmart today. Our technical team usually responds within one business day.
Why Choose CoRound
The cove base that goes in with the panels. Rigid PVC profiles with flexible co-extruded lips and pre-formed corners. Designed for walk-in coolers, food plants and commercial kitchens.
Flexible lip
On standard cold storage panels with mesa or wide-rib profiles, the flexible lip follows the ribs.
Factory-formed curve
The curve comes from the factory, not from the installer’s hand: it is the same all the way around the room.
One pass along the wall
Installing CoRound is one pass along the wall: fasten the profile and snap in the corners. There is nothing to mix, trowel, weld or cure, and no sealant line is required along the wall.
Sanitary design
The rounded profile removes the square corner where dirt builds up, and the smooth, non-porous surface is easy to clean.
Replaceable lengths
A damaged length can be replaced on its own: the rest of the run stays in place. The first CoRound installations date back to 2010.
Temperature
Operating temperature: −4 °F to +140 °F. For colder applications, contact us.
Technical Specs
Technical data for this piece. Available by the box or by the piece.
| Material | PVC with flexible edges |
| Profile Height | 3.9 in |
| Packing | 100 pcs/box |
| Operating temperature | −4 °F to +140 °F. For colder applications, contact us. |
| Color Options | Pure White 9010, Sand White 9002 |
| Chemical Resistance | Resistant to common cleaning chemicals |
Applications
Designed for walk-in coolers, food plants and commercial kitchens.
Cold Storage
PVC is a thermal-break material: it conducts far less heat than metal.
✓ Walk-in coolers
✓ Freezers
✓ Refrigerated warehouses
Food Processing
Resistant to common cleaning chemicals; can be washed with water up to +140 °F.
✓ Meat
✓ Dairy
✓ Bakery
✓ Beverage production
Cleanrooms and Labs
Applications also include cleanrooms and pharmaceutical facilities.
✓ Cleanrooms
✓ Laboratories
✓ Pharmaceutical facilities
Commercial Kitchens
In a room already in operation, CoRound can be installed on the finished floor: there is no floor to redo and nothing to cure.
✓ Restaurants
✓ Commissaries
✓ Food service
Installation Positions
Wall-to-Floor Sanitary Juncture
Frequently Asked Questions
What exactly are sanitary PVC profiles?
Sanitary PVC profiles, also called sanitary cove base, round off the corner where two surfaces meet: floor and wall, wall and wall, or wall and ceiling. The rounded profile removes the square corner where dirt builds up, and the smooth, non-porous surface is easy to clean. CoRound profiles are precision-extruded from rigid PVC, with flexible co-extruded lips on the cove base and the sanitary base.
Why not just use traditional silicone sealant for corner junctions?
Exposed sealant can need cleaning and, over time, redoing: each time that means a service call, material and labor. With CoRound, no sealant line is required along the wall. The system has pre-formed corners, no silicone-filled field cuts. Silicone is optional: not required for installation.
Where are CoRound profiles used?
Applications include walk-in coolers and freezers, food plants, commercial kitchens, cleanrooms and pharmaceutical facilities. Installs on insulated panels, FRP-covered walls, tile, masonry and drywall. PVC is a thermal-break material: it conducts far less heat than metal.
Can CoRound profiles be used in walk-in coolers and freezers?
Walk-in coolers and freezers are among the applications of CoRound profiles. Operating temperature: −4 °F to +140 °F. For colder applications, contact us.
How do sanitary PVC profiles compare with tile or metal bases?
A tile cove base has grout lines, and grout can hold dirt and moisture. CoRound profiles have a smooth PVC surface with no grout lines. Metal bases and channels can rust where water sits. PVC does not rust. CoRound costs less than stainless steel.
What’s the difference between a standard baseboard and a sanitary profile like CoR Skirt?
The CoR Skirt is a rigid PVC sanitary base with a rounded profile and flexible co-extruded lips. Unlike a rubber base, it can be screwed or riveted to the wall, so it doesn’t have to depend on adhesive. When the CoR Skirt is screwed or riveted, the fasteners sit behind a snap-on cover strip: no exposed screw heads to collect dirt.
How do the flexible lips work?
- CoR Skirt sanitary base: Flexible co-extruded lips press against the wall and the floor and follow small surface irregularities, closing the juncture. In wet areas, installers can add a thin bead of neutral silicone to help keep water from getting behind the profile.
- CoR 4 cove base: Flexible co-extruded lips press against both walls, or the wall and the ceiling, and follow small surface irregularities, closing the junction.
On standard cold storage panels with mesa or wide-rib profiles, the flexible lip follows the ribs. Silicone is optional: not required for installation.
Is installation complicated? Do I need a specialized technician?
The panel crew can install the profiles: no separate flooring or welding crew to schedule.
The CoR Skirt is screwed or riveted to the wall, or bonded with adhesive: installer’s choice. The CoR 4 snaps onto the CoR 4 Base, which is pre-drilled and fastened with screws or rivets. Corners, joints and end caps press or snap into place.
Do I need to purchase special accessory pieces for corners and junctions?
Yes, and that’s one of the strengths of a complete system like CoRound. One system for the whole room: base track, sanitary base or heavy-duty curb, cove base for wall and ceiling junctions, pre-formed corners, end caps and corner guards, all made to fit together. CoRound Basic for cost-sensitive projects; CoRound Seal adds corner pieces and end caps with flexible lips.
What maintenance do CoRound profiles need?
Resistant to common cleaning chemicals; can be washed with water up to +140 °F. PVC does not rust. The first CoRound installations date back to 2010.
Related Products
CoR Skirt S
Sanitary base for the wall-floor juncture.
CoR Skirt S 2-Way Internal Corner
Pre-formed inside corner for two CoR Skirt runs, used where there is no vertical cove base. With flexible edges.
CoR Skirt S 2-Way External Corner
Pre-formed outside corner for the CoR Skirt, for columns and outside wall corners. With flexible edges.
CoR Skirt S 3-Way Internal Corner
Pre-formed inside corner where two CoR Skirt runs and the vertical CoR 4 meet. With flexible edges.
CoR Skirt S End Left
Left-hand end cap that closes a CoR Skirt run, for example at a door. With flexible edges.
CoR Skirt S End Right
Right-hand end cap that closes a CoR Skirt run, for example at a door. With flexible edges.
Call
+1 786 917 8106 (phone and WhatsApp)
Address
13230 SW 132nd Avenue, Unit B4, Miami, FL 33186 · Mon–Fri 8am–5pm ET